Table of Contents
Drum sanders are equipped with sandpaper. It’s a powerful electrical tool used to smoothen the surface of hardwood. However, sometimes, sanding with drum sanders give irregular finishes to surfaces that are hazardous for homeowners.
Refresh your hardwood floor to create a good-looking home. You can do it by yourself without breaking the bank you need to prepare yourself. Before sanding, you need to wear a mask and eye and ear protection. The room should be closed from the outside because it creates clouds of dust. After you have decided that you need drum sanders, you can get it here.
Things You Should Keep in Mind
First, you need to decide whether the floor needs refinishing or not. Before starting to work on the job, check for the following:
- Drop some water and see if its soaks slowly; you may get the job done done by polishing. If it soaks immediately, then you need to refinish the floors because the wood fibers are damaged.
- If the floor is deeply stained, damaged, and/or warped, then you need to repair it first and then refinish it.
- If your floor is less than 3/4”, you have to hire a professional to refinish it. If the floor is as thin as 1/4”, you cannot refinish it.
- An engineered wood cannot be sanded as many times as a hardwood.
Preparing to Refinish Your Floor
Step 1: Clean the Room
You need to remove every piece of furniture in your room. If the floor is attached to anything, remove them. Cover the air vents, lights, windows, and doors so that they will not get dusty. Tape over every opening, including electrical switches, vent ducts, and other outlets. Seal the room fully from outside by using masking tape and plastic sheets. To get rid of the dirt from the floor after, vacuum the floor before sanding.
Step 2: Remove Objects
If you have decided to remove carpet, it’s time to peel back the carpet staples underneath so that it will not tear the paper on the floor sander. Remove all doors and shoe molding. Next, do a close inspection to the floor and drive in any nail heads.
Step 3: Start Sanding
Proper sanding on the floor brings back the perfection of the hardwood floor. Several steps must be followed to get the smooth finishing.
First, use the random orbital sander for flat floors. It’s easier to handle the random sanding pattern because it won’t leave directional scratches on the floor. If your floor is cupped and wavy, use the drum sander on the floor. Many homeowners don’t keep this drum sander in their rental tool collection. If you’ve never used a drum sander, you may have to go through some exciting surprises. It’s large and noisy, but it removes a lot of material quickly.
Here are Some Things You Should be Aware Of:
- Start the sanding machine while it’s tilted back. Then, slowly lower it on the surface and start sanding.
- You need to choose sanding grit according to your floor. Generally, it starts with 20 to 60 and ends with 120 or more. You can skip the 20 grit if your floor is relatively smooth. Always use the same grit in every area.
- Keep the machine moving, and don’t let it stand still while using it.
- Remember to clean the floor thoroughly after each sanding grit change.
- Work slowly and carefully. Let the machine do its job.
You Need to Secure Damage by Following Some Steps Below:
1. Load the drum sander machine with coarse-grit (30-40 grit) sandpaper. Don’t let it stay in one spot or you will damage the floor. Use a power hand sander to sand the edges. To sand the corners, use a detail sander with the same grit paper.
2. Sand it straight with the grain because it is easier this way.
3. After sanding is done, vacuum with a brush attachment.
4. Fill in the deep gouges and holes with matching wood filler before you sand the next grit.
5. As for the second round with the sander, use medium-grit (50-60 grit) sandpaper. The same goes for the power hand and detail sander. Again, clean up the dust with a vacuum and brush attachment.
6. To do the final sanding pass with the sander, use fine-grit (80-100 grit) sandpaper in those sanders. Then vacuum thoroughly with a brush attachment again.
7. Use a damp mop on the floor to pick up any remaining particles.
8. If the floor feels rough after sanding, buff it with a 120-grit screen. Buffing with a screen smoothens the scratches. Buff along the grain and get as close as possible to the walls. Use the sanding screen for the edges and corners, too.
9. Go over the floor with a cloth dampened with mineral spirits. Check local fire regulations for disposal instructions.
Step 4: Staining your floor
To stain your floor, provide a water or oil-based clear sealer to your refinished floor. It’s interesting to pick a new stain color such as rich mahogany, or dark oak. These colors are very valuable in the market now. Darker colors make the dust particles more noticeable.
So, choose the stain color you want to apply to your hardwood. You need to follow the following instructions on the product you are going to use. Try to test in a small area before you start staining your entire floor. It’s important to dry the floor before moving all the furniture. Avoid sliding the furniture on the floor if you can help it. You can also reattach shoe molding. Finally, your worn-out hardwood is reborn with a fresh finish.